[Fwd: fax from Behringer Corp.]

Discussion:

(too old to reply)

hylafax-user

2009-05-27 12:31:04 UTC

This is a multi-part message in MIME format.

--Boundary_(ID_UlMe4A0dlruVJFkUTd1EXw)
Content-type: text/plain; charset=ISO-8859-1; format=flowed
Content-transfer-encoding: 7BIT

Hi,

7:10:43 system() failed: No such file or directory.

Increase the log level ("debug 9"). It will tell you what program mgetty
is calling here - read: what was compiled in as FAX_NOTIFY_PROGRAM.

A policy.h file sounds like it would be used in compiling a new version
of Mgetty. Since I don't have policy.h where would I add the
FAX_NOTIFY_PROGRAM line?

If you have the source bundle, you have a policy.h-dist, and you have
a "README.1st". Guess what this is for :-)

I don't have the source bundle. I did read the README.1st and clicked
through the link to mgetty.greenie.net reading the receiving faxes
section which again points to policy.h or policy.h-dist.
I changed debug from 8 to 9 but don't see any difference in the log when
I receive faxes.

I reloaded mgetty after changing the /etc/mgetty+sendfax/mgetty.config

Here's the log:

05/27 08:16:22 ##### failed dev=ttyS0, pid=7497, got signal 15, exiting
--
05/27 08:16:41 yS0 mgetty: experimental test release 1.1.30-Dec16
05/27 08:16:41 yS0 check for lockfiles
05/27 08:16:41 yS0 locking the line
05/27 08:16:41 yS0 lowering DTR to reset Modem
05/27 08:16:42 yS0 send: \dATQ0V1H0[0d]
05/27 08:16:42 yS0 waiting for ``OK'' ** found **
05/27 08:16:43 yS0 send: ATS0=0Q0&D3&C1[0d]
05/27 08:16:43 yS0 waiting for ``OK'' ** found **
05/27 08:16:43 yS0 mdm_send: 'ATI'
05/27 08:16:43 yS0 USR Courier/Sportster 56k detected
05/27 08:16:43 yS0 mdm_send: 'ATI3'
05/27 08:16:43 yS0 additional info: 'U.S. Robotics 56K FAX EXT V5.11.6'
05/27 08:16:43 yS0 mdm_send: 'AT+FCLASS=2.0' -> OK
05/27 08:16:43 yS0 mdm_send: 'AT+FAA=1;+FCR=1' -> OK
05/27 08:16:44 yS0 mdm_send: 'AT+FBO=1' -> OK
05/27 08:16:44 yS0 mdm_send: 'AT+FNR=1,1,1,0' -> OK
05/27 08:16:44 yS0 mdm_send: 'AT+FLI="973 697 4443"' -> OK
05/27 08:16:44 yS0 mdm_send: 'AT+FCC=1,5,0,2,0,0,0,0' -> OK
05/27 08:16:45 yS0 waiting...
05/27 08:17:54 yS0 wfr: waiting for ``RING''
05/27 08:17:54 yS0 send: ATA[0d]
05/27 08:17:54 yS0 waiting for ``CONNECT''
05/27 08:18:00 yS0 found action string: ``+FCO_''
05/27 08:18:00 yS0 start fax receiver...
05/27 08:18:00 yS0 fax_wait_for(OK)
05/27 08:18:02 yS0 fax_id: '+FTI:" removed.Corp."'
05/27 08:18:02 yS0 transmission par.: '+FCS:1,5,0,2,0,0,0,0'** found **
05/27 08:18:02 yS0 mdm_send: 'AT+FLO=2' -> OK
05/27 08:18:02 yS0 fax_send: 'AT+FDR'
05/27 08:18:02 yS0 fax_wait_for(CONNECT)** found **
05/27 08:18:07 yS0 fax_get_page_data: receiving
/var/spool/fax/incoming/ffa1d2f72S0-Behringer-Corp.01...
05/27 08:18:32 yS0 fax_get_page_data: page end, bytes received: 44318
05/27 08:18:32 yS0 fax_wait_for(OK)
05/27 08:18:32 yS0 page status: +FPS:1,2163,0,0,0** found **
05/27 08:18:33 yS0 fax_send: 'AT+FDR'
05/27 08:18:33 yS0 fax_wait_for(CONNECT)
05/27 08:18:37 yS0 connection hangup: '+FHS:00'** found **
05/27 08:18:37 ##### fax dev=ttyS0, pid=8328, caller='none', name='',
id='removed.', +FHNG=000, pages=1/0, time=00:00:43
05/27 08:18:37 yS0 system() failed: No such file or directory
05/27 08:18:39 yS0 mdm_send: 'ATH0' -> OK
--
05/27 08:18:39 yS0 mgetty: experimental test release 1.1.30-Dec16
05/27 08:18:39 yS0 check for lockfiles
05/27 08:18:39 yS0 locking the line
05/27 08:18:39 yS0 lowering DTR to reset Modem
05/27 08:18:40 yS0 send: \dATQ0V1H0[0d]
05/27 08:18:41 yS0 waiting for ``OK'' ** found **
05/27 08:18:41 yS0 send: ATS0=0Q0&D3&C1[0d]
05/27 08:18:41 yS0 waiting for ``OK'' ** found **
05/27 08:18:41 yS0 mdm_send: 'ATI'
05/27 08:18:41 yS0 USR Courier/Sportster 56k detected
05/27 08:18:41 yS0 mdm_send: 'ATI3'
05/27 08:18:41 yS0 additional info: 'U.S. Robotics 56K FAX EXT V5.11.6'
05/27 08:18:41 yS0 mdm_send: 'AT+FCLASS=2.0' -> OK
05/27 08:18:42 yS0 mdm_send: 'AT+FAA=1;+FCR=1' -> OK
05/27 08:18:42 yS0 mdm_send: 'AT+FBO=1' -> OK
05/27 08:18:42 yS0 mdm_send: 'AT+FNR=1,1,1,0' -> OK
05/27 08:18:42 yS0 mdm_send: 'AT+FLI="973 697 4443"' -> OK
05/27 08:18:42 yS0 mdm_send: 'AT+FCC=1,5,0,2,0,0,0,0' -> OK
05/27 08:18:43 yS0 waiting...[***@vrod log]#

Here's the mgetty.config

cat mgetty.config
#
# mgetty configuration file
#
# this is a sample configuration file, see mgetty.info for details
#
# comment lines start with a "#", empty lines are ignored

# ----- global section -----
#
# In this section, you put the global defaults, per-port stuff is below

# set the global debug level to "4" (default from policy.h)

# set the local fax station id

# access the modem(s) with 38400 bps

# use these options to make the /dev/tty-device owned by "uucp.uucp"
# and mode "rw-rw-r--" (0664). *LEADING ZERO NEEDED!*
#port-owner uucp
#port-group uucp
#port-mode 0664

# use these options to make incoming faxes owned by "root.uucp"
# and mode "rw-r-----" (0640). *LEADING ZERO NEEDED!*
#fax-owner root
#fax-group uucp
#fax-mode 0640

# ----- port specific section -----
#
# Here you can put things that are valid only for one line, not the others
#

# Zoom V.FX 28.8, connected to ttyS0: don't do fax, less logging
#
#port ttyS0
# debug 3
# data-only y

# some other Rockwell modem, needs "switchbd 19200" to receive faxes
# properly (otherwise it will fail with "timeout").
#
#port ttyS1
# speed 38400
# switchbd 19200

# ZyXEL 2864, connected to ttyS2: maximum debugging, grab statistics
#
#port ttyS2
# debug 8
# init-chat "" \d\d\d+++\d\d\dAT&FS2=255 OK ATN3S0=0S13.2=1 OK
# statistics-chat "" AT OK ATI2 OK
# statistics-file /var/log/statistics.ttyS2
# modem-type cls2

# direct connection of a VT100 terminal which doesn't like DTR drops
#
#port ttyS3
# direct y
# speed 19200
# toggle-dtr n
fax-id 973 697 4443
fax-owner root
port /dev/modem
debug 9
fax-id 973 697 4443
speed 115200
init-chat ATM0DT
port-owner ppp
port-group pppusers
port-mode 0664

-------- Original Message --------
Subject: fax from Behringer Corp.
Date: Wed, 27 May 2009 08:18:37 -0400
From: ***@vrod.rownetco.com (Fax Getty)
To: ***@vrod.rownetco.com

A fax was successfully received:
Sender ID: removed Corp.
Pages received: 1

Modem device: ttyS0

Communication parameters: +FCS:1,5,0,2,0,0,0,0
Resolution : fine
Bit Rate : 14400
Page Width : 1728 pixels
Page Length: unlimited
Compression: 0 (1d mod Huffman)
Error Corr.: none
Scan Time : 0

Reception Time : 00:43

Spooled G3 fax files:

/var/spool/fax/incoming/ffa1d2f72S0-removed-Corp.01

regards, your modem subsystem.

--Boundary_(ID_UlMe4A0dlruVJFkUTd1EXw)
Content-type: text/html; charset=ISO-8859-1
Content-transfer-encoding: 7BIT

<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
</head>
<body bgcolor="#ffffff" text="#000000">
<pre wrap="">Hi,

On Wed, May 27, 2009 at 07:18:38AM -0400, hylafax-user wrote: </pre> <blockquote type="cite"> <pre wrap="">> 7:10:43 system() failed: No such file or directory.
</pre>
</blockquote>
<pre wrap="">
Increase the log level ("debug 9"). It will tell you what program mgetty
is calling here - read: what was compiled in as FAX_NOTIFY_PROGRAM. </pre> <blockquote type="cite"> <pre wrap="">> A policy.h file sounds like it would be used in compiling a new version > of Mgetty. Since I don't have policy.h where would I add the > FAX_NOTIFY_PROGRAM line?
</pre>
</blockquote>
<pre wrap="">
If you have the source bundle, you have a policy.h-dist, and you have
a "README.1st". Guess what this is for :-) 
</pre>
 
I don't have the source bundle.  I did read the README.1st and clicked
through the link to mgetty.greenie.net reading the receiving faxes
section which again points to policy.h or policy.h-dist. 
I changed debug from 8 to 9 but don't see any difference in the log
when I receive faxes. 
 
I reloaded mgetty after changing the /etc/mgetty+sendfax/mgetty.config 
 
Here's the log: 
 
05/27 08:16:22 ##### failed dev=ttyS0, pid=7497, got signal 15, exiting 
-- 
05/27 08:16:41 yS0  mgetty: experimental test release 1.1.30-Dec16 
05/27 08:16:41 yS0  check for lockfiles 
05/27 08:16:41 yS0  locking the line 
05/27 08:16:41 yS0  lowering DTR to reset Modem 
05/27 08:16:42 yS0  send: \dATQ0V1H0[0d] 
05/27 08:16:42 yS0  waiting for ``OK'' ** found ** 
05/27 08:16:43 yS0  send: ATS0=0Q0&D3&C1[0d] 
05/27 08:16:43 yS0  waiting for ``OK'' ** found ** 
05/27 08:16:43 yS0  mdm_send: 'ATI' 
05/27 08:16:43 yS0  USR Courier/Sportster 56k detected 
05/27 08:16:43 yS0  mdm_send: 'ATI3' 
05/27 08:16:43 yS0  additional info: 'U.S. Robotics 56K FAX EXT V5.11.6' 
05/27 08:16:43 yS0  mdm_send: 'AT+FCLASS=2.0' -> OK 
05/27 08:16:43 yS0  mdm_send: 'AT+FAA=1;+FCR=1' -> OK 
05/27 08:16:44 yS0  mdm_send: 'AT+FBO=1' -> OK 
05/27 08:16:44 yS0  mdm_send: 'AT+FNR=1,1,1,0' -> OK 
05/27 08:16:44 yS0  mdm_send: 'AT+FLI="973 697 4443"' -> OK 
05/27 08:16:44 yS0  mdm_send: 'AT+FCC=1,5,0,2,0,0,0,0' -> OK 
05/27 08:16:45 yS0  waiting... 
05/27 08:17:54 yS0  wfr: waiting for ``RING'' 
05/27 08:17:54 yS0  send: ATA[0d] 
05/27 08:17:54 yS0  waiting for ``CONNECT'' 
05/27 08:18:00 yS0  found action string: ``+FCO_'' 
05/27 08:18:00 yS0  start fax receiver... 
05/27 08:18:00 yS0  fax_wait_for(OK) 
05/27 08:18:02 yS0  fax_id: '+FTI:"     removed.Corp."' 
05/27 08:18:02 yS0  transmission par.: '+FCS:1,5,0,2,0,0,0,0'** found ** 
05/27 08:18:02 yS0  mdm_send: 'AT+FLO=2' -> OK 
05/27 08:18:02 yS0  fax_send: 'AT+FDR' 
05/27 08:18:02 yS0  fax_wait_for(CONNECT)** found ** 
05/27 08:18:07 yS0  fax_get_page_data: receiving
/var/spool/fax/incoming/ffa1d2f72S0-Behringer-Corp.01... 
05/27 08:18:32 yS0  fax_get_page_data: page end, bytes received: 44318 
05/27 08:18:32 yS0  fax_wait_for(OK) 
05/27 08:18:32 yS0  page status: +FPS:1,2163,0,0,0** found ** 
05/27 08:18:33 yS0  fax_send: 'AT+FDR' 
05/27 08:18:33 yS0  fax_wait_for(CONNECT) 
05/27 08:18:37 yS0  connection hangup: '+FHS:00'** found ** 
05/27 08:18:37 ##### fax dev=ttyS0, pid=8328, caller='none', name='',
id='removed.', +FHNG=000, pages=1/0, time=00:00:43 
05/27 08:18:37 yS0  system() failed: No such file or directory 
05/27 08:18:39 yS0  mdm_send: 'ATH0' -> OK 
-- 
05/27 08:18:39 yS0  mgetty: experimental test release 1.1.30-Dec16 
05/27 08:18:39 yS0  check for lockfiles 
05/27 08:18:39 yS0  locking the line 
05/27 08:18:39 yS0  lowering DTR to reset Modem 
05/27 08:18:40 yS0  send: \dATQ0V1H0[0d] 
05/27 08:18:41 yS0  waiting for ``OK'' ** found ** 
05/27 08:18:41 yS0  send: ATS0=0Q0&D3&C1[0d] 
05/27 08:18:41 yS0  waiting for ``OK'' ** found ** 
05/27 08:18:41 yS0  mdm_send: 'ATI' 
05/27 08:18:41 yS0  USR Courier/Sportster 56k detected 
05/27 08:18:41 yS0  mdm_send: 'ATI3' 
05/27 08:18:41 yS0  additional info: 'U.S. Robotics 56K FAX EXT V5.11.6' 
05/27 08:18:41 yS0  mdm_send: 'AT+FCLASS=2.0' -> OK 
05/27 08:18:42 yS0  mdm_send: 'AT+FAA=1;+FCR=1' -> OK 
05/27 08:18:42 yS0  mdm_send: 'AT+FBO=1' -> OK 
05/27 08:18:42 yS0  mdm_send: 'AT+FNR=1,1,1,0' -> OK 
05/27 08:18:42 yS0  mdm_send: 'AT+FLI="973 697 4443"' -> OK 
05/27 08:18:42 yS0  mdm_send: 'AT+FCC=1,5,0,2,0,0,0,0' -> OK 
05/27 08:18:43 yS0  waiting...[***@vrod log]# 
 
 
Here's the mgetty.config 
 
cat mgetty.config 
# 
# mgetty configuration file 
# 
# this is a sample configuration file, see mgetty.info for details 
# 
# comment lines start with a "#", empty lines are ignored 
 
 
# ----- global section ----- 
# 
# In this section, you put the global defaults, per-port stuff is below 
 
 
# set the global debug level to "4" (default from policy.h) 
 
# set the local fax station id 
 
# access the modem(s) with 38400 bps 
 
#  use these options to make the /dev/tty-device owned by "uucp.uucp" 
#  and mode "rw-rw-r--" (0664). *LEADING ZERO NEEDED!* 
#port-owner uucp 
#port-group uucp 
#port-mode 0664 
 
#  use these options to make incoming faxes owned by "root.uucp" 
#  and mode "rw-r-----" (0640). *LEADING ZERO NEEDED!* 
#fax-owner root 
#fax-group uucp 
#fax-mode 0640 
 
 
# ----- port specific section ----- 
# 
# Here you can put things that are valid only for one line, not the
others 
# 
 
# Zoom V.FX 28.8, connected to ttyS0: don't do fax, less logging 
# 
#port ttyS0 
#  debug 3 
#  data-only y 
 
# some other Rockwell modem, needs "switchbd 19200" to receive faxes 
# properly (otherwise it will fail with "timeout"). 
# 
#port ttyS1 
#  speed 38400 
#  switchbd 19200 
 
# ZyXEL 2864, connected to ttyS2: maximum debugging, grab statistics 
# 
#port ttyS2 
#  debug 8 
#  init-chat "" \d\d\d+++\d\d\dAT&FS2=255 OK ATN3S0=0S13.2=1 OK 
#  statistics-chat "" AT OK ATI2 OK 
#  statistics-file /var/log/statistics.ttyS2 
#  modem-type cls2 
 
# direct connection of a VT100 terminal which doesn't like DTR drops 
# 
#port ttyS3 
#  direct y 
#  speed 19200 
#  toggle-dtr n 
fax-id 973 697 4443 
fax-owner root 
port /dev/modem 
debug 9 
fax-id 973 697 4443 
speed 115200 
init-chat ATM0DT 
port-owner ppp 
port-group pppusers 
port-mode 0664 
 
 
-------- Original Message --------
<table class="moz-email-headers-table" border="0" cellpadding="0"
cellspacing="0">
<tbody>
<tr>
<th align="right" nowrap="nowrap" valign="baseline">Subject: </th>
<td>fax from Behringer Corp.</td>
</tr>
<tr>
<th align="right" nowrap="nowrap" valign="baseline">Date: </th>
<td>Wed, 27 May 2009 08:18:37 -0400</td>
</tr>
<tr>
<th align="right" nowrap="nowrap" valign="baseline">From: </th>
<td><a class="moz-txt-link-abbreviated" href="mailto:***@vrod.rownetco.com">***@vrod.rownetco.com</a> (Fax Getty)</td>
</tr>
<tr>
<th align="right" nowrap="nowrap" valign="baseline">To: </th>
<td><a class="moz-txt-link-abbreviated" href="mailto:***@vrod.rownetco.com">***@vrod.rownetco.com</a></td>
</tr>
</tbody>
</table>
 
 
<pre>A fax was successfully received:
Sender ID: removed Corp.
Pages received: 1

Modem device: ttyS0

Communication parameters: +FCS:1,5,0,2,0,0,0,0
Resolution : fine
Bit Rate : 14400
Page Width : 1728 pixels
Page Length: unlimited
Compression: 0 (1d mod Huffman)
Error Corr.: none
Scan Time : 0

Reception Time : 00:43

Spooled G3 fax files:

/var/spool/fax/incoming/ffa1d2f72S0-removed-Corp.01

regards, your modem subsystem.

</pre>
</body>
</html>

--Boundary_(ID_UlMe4A0dlruVJFkUTd1EXw)--

Gert Doering

2009-05-27 18:14:37 UTC

Permalink

Hi,

Post by hylafax-user

A policy.h file sounds like it would be used in compiling a new version
of Mgetty. Since I don't have policy.h where would I add the
FAX_NOTIFY_PROGRAM line?

If you have the source bundle, you have a policy.h-dist, and you have
a "README.1st". Guess what this is for :-)

I don't have the source bundle. I did read the README.1st and clicked
through the link to mgetty.greenie.net reading the receiving faxes
section which again points to policy.h or policy.h-dist.
I changed debug from 8 to 9 but don't see any difference in the log when

Well, there's a download link on mgetty.greenie.net - but anyway,
thus should be doable without recompiling.

Post by hylafax-user
I reloaded mgetty after changing the /etc/mgetty+sendfax/mgetty.config

[..]

Post by hylafax-user
05/27 08:16:43 yS0 additional info: 'U.S. Robotics 56K FAX EXT V5.11.6'
05/27 08:16:43 yS0 mdm_send: 'AT+FCLASS=2.0' -> OK
05/27 08:16:43 yS0 mdm_send: 'AT+FAA=1;+FCR=1' -> OK

I'm not exactly sure what happened, but this is still "debug 4" level
(maybe you added the "debug 9" to an inactive "port" section in the
config file).

Try adding "-x 9" to the command line in /etc/inittab - this will
override whatever is in the config file.

Post by hylafax-user
Here's the mgetty.config
# direct connection of a VT100 terminal which doesn't like DTR drops
#
#port ttyS3
# direct y
# speed 19200
# toggle-dtr n
fax-id 973 697 4443
fax-owner root
port /dev/modem
debug 9
fax-id 973 697 4443
speed 115200
init-chat ATM0DT
port-owner ppp
port-group pppusers
port-mode 0664

These config statements will never be used, because they are behind
a section "port /dev/modem" - but your mgetty is running on "ttyS0".

This will never ever be evaluated, because the "port xxx" statement
must be without "/dev/" - and of course it must be the very same
device node that's put on the mgetty command line (ttyS0, without /dev/)

gert

--
USENET is *not* the non-clickable part of WWW!
//www.muc.de/~gert/
Gert Doering - Munich, Germany ***@greenie.muc.de
fax: +49-89-35655025 ***@net.informatik.tu-muenchen.de

--
Posted automagically by a mail2news gateway at muc.de e.V.
Please direct questions, flames, donations, etc. to news-***@muc.de

hylafax-user

2009-05-28 00:13:54 UTC

Permalink

This is a multi-part message in MIME format.

--Boundary_(ID_ZB5oA1b4iD+D83ikIEElXw)
Content-type: text/plain; charset=ISO-8859-1; format=flowed
Content-transfer-encoding: 7BIT

Post by Gert Doering
Hi,

Post by hylafax-user

A policy.h file sounds like it would be used in compiling a new version
of Mgetty. Since I don't have policy.h where would I add the
FAX_NOTIFY_PROGRAM line?

If you have the source bundle, you have a policy.h-dist, and you have
a "README.1st". Guess what this is for :-)

Well, there's a download link on mgetty.greenie.net - but anyway,
thus should be doable without recompiling.

Post by hylafax-user
I reloaded mgetty after changing the /etc/mgetty+sendfax/mgetty.config

[..]

Post by hylafax-user
05/27 08:16:43 yS0 additional info: 'U.S. Robotics 56K FAX EXT V5.11.6'
05/27 08:16:43 yS0 mdm_send: 'AT+FCLASS=2.0' -> OK
05/27 08:16:43 yS0 mdm_send: 'AT+FAA=1;+FCR=1' -> OK

I'm not exactly sure what happened, but this is still "debug 4" level
(maybe you added the "debug 9" to an inactive "port" section in the
config file).
Try adding "-x 9" to the command line in /etc/inittab - this will
override whatever is in the config file.

These config statements will never be used, because they are behind
a section "port /dev/modem" - but your mgetty is running on "ttyS0".
This will never ever be evaluated, because the "port xxx" statement
must be without "/dev/" - and of course it must be the very same
device node that's put on the mgetty command line (ttyS0, without /dev/)
gert

All the while I thought the /dev/modem was how mgetty was working. I
guess it was using compiled defaults.
I changed the port statement to just say port ttyS0, of course then the
modem refused to answere because of the init-chat statement a few lines
down.
I commented that out along with the port-owner, port-group and port-mode
statements (I had at one time been set up to allow dial-in PPP).

The log below is post changes. You'd indicated we'd be able to get the
fax notify issue resolved without recompiling but didn't get into
details (probably
because you'd found the /dev/modem issue.

05/27 20:01:45 ##### failed dev=ttyS0, pid=5251, got signal 15, exiting

--
05/27 20:01:58 yS0 mgetty: experimental test release 1.1.30-Dec16
05/27 20:01:58 yS0 check for lockfiles
05/27 20:01:58 yS0 checklock: stat failed, no file
05/27 20:01:58 yS0 locking the line
05/27 20:01:58 yS0 makelock(ttyS0) called
05/27 20:01:58 yS0 do_makelock: lock='/var/lock/LCK..ttyS0'
05/27 20:01:58 yS0 lock made
05/27 20:01:59 yS0 tio_get_rs232_lines: status: RTS CTS DSR DTR
05/27 20:01:59 yS0 lowering DTR to reset Modem
05/27 20:01:59 yS0 tss: set speed to 115200 (10002)
05/27 20:01:59 yS0 tio_set_flow_control( HARD )
05/27 20:01:59 yS0 waiting for line to clear (VTIME), read:
05/27 20:01:59 yS0 send: \dATQ0V1H0[0d]
05/27 20:02:00 yS0 waiting for ``OK''
05/27 20:02:00 yS0 got: [0d][0a]OK ** found **
05/27 20:02:00 yS0 send: ATS0=0Q0&D3&C1[0d]
05/27 20:02:00 yS0 waiting for ``OK''
05/27 20:02:00 yS0 got: [0d]
05/27 20:02:00 yS0 CND: OK[0a][0d][0a]OK ** found **
05/27 20:02:00 yS0 mdm_send: 'ATI'
05/27 20:02:00 yS0 got:[0d][0a][0d][0a]5601[0d]
05/27 20:02:00 yS0 mdm_gis: string 1: '5601'
05/27 20:02:00 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:02:00 yS0 mdm_identify: string '5601'
05/27 20:02:00 yS0 USR Courier/Sportster 56k detected
05/27 20:02:00 yS0 mdm_send: 'ATI3'
05/27 20:02:00 yS0 got:[0a][0d][0a]U.S. Robotics 56K FAX EXT V5.11.6[0d]
05/27 20:02:00 yS0 mdm_gis: string 1: 'U.S. Robotics 56K FAX EXT V5.11.6'
05/27 20:02:00 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:02:01 yS0 additional info: 'U.S. Robotics 56K FAX EXT V5.11.6'
05/27 20:02:01 yS0 mdm_send: 'AT+FCLASS=2.0'
05/27 20:02:01 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:02:01 yS0 mdm_command: string 'OK' -> OK
05/27 20:02:01 yS0 mdm_send: 'AT+FAA=1;+FCR=1'
05/27 20:02:01 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:02:01 yS0 mdm_command: string 'OK' -> OK
05/27 20:02:01 yS0 mdm_send: 'AT+FBO=1'
05/27 20:02:01 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:02:01 yS0 mdm_command: string 'OK' -> OK
05/27 20:02:01 yS0 mdm_send: 'AT+FNR=1,1,1,0'
05/27 20:02:01 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:02:01 yS0 mdm_command: string 'OK' -> OK
05/27 20:02:01 yS0 mdm_send: 'AT+FLI="973 697 4443"'
05/27 20:02:01 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:02:02 yS0 mdm_command: string 'OK' -> OK
05/27 20:02:02 yS0 mdm_send: 'AT+FCC=1,5,0,2,0,0,0,0'
05/27 20:02:02 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:02:02 yS0 mdm_command: string 'OK' -> OK
05/27 20:02:02 yS0 waiting for line to clear (VTIME), read:
05/27 20:02:02 yS0 removing lock file
05/27 20:02:02 yS0 waiting...
05/27 20:02:34 yS0 select returned 1
05/27 20:02:34 yS0 checking lockfiles, locking the line
05/27 20:02:34 yS0 makelock(ttyS0) called
05/27 20:02:34 yS0 do_makelock: lock='/var/lock/LCK..ttyS0'
05/27 20:02:34 yS0 lock made
05/27 20:02:34 yS0 wfr: waiting for ``RING''
05/27 20:02:34 yS0 got: [0a][0d][0a]RING[0d]
05/27 20:02:34 yS0 CND: RING
05/27 20:02:34 yS0 wfr: rc=0, drn=0
05/27 20:02:34 yS0 CND: check no: 'none'
05/27 20:02:34 yS0 send: ATA[0d]
05/27 20:02:34 yS0 waiting for ``CONNECT''
05/27 20:02:34 yS0 got: [0d]
05/27 20:02:44 yS0 CND: OK[0a]+FCO[0d]
05/27 20:02:44 yS0 CND: +FCO
05/27 20:02:44 yS0 found action string: ``+FCO_''
05/27 20:02:44 yS0 start fax receiver...
05/27 20:02:44 yS0 fax receiver: entry
05/27 20:02:44 yS0 fax_wait_for(OK)
05/27 20:02:44 yS0 got:[0a][0a][0d][0a]+FTI:" Behringer Corp."[0d]
05/27 20:02:46 yS0 fax_wait_for: string '+FTI:" Behringer Corp."'
05/27 20:02:46 yS0 fax_id: '+FTI:" Behringer Corp."'
05/27 20:02:46 yS0 got:[0a][0d][0a]+FCS:1,5,0,2,0,0,0,0[0d]
05/27 20:02:46 yS0 fax_wait_for: string '+FCS:1,5,0,2,0,0,0,0'
05/27 20:02:46 yS0 transmission par.: '+FCS:1,5,0,2,0,0,0,0'
05/27 20:02:46 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:02:46 yS0 fax_wait_for: string 'OK'** found **
05/27 20:02:46 yS0 looking for utmp entry... (my PID: 5871)
05/27 20:02:46 yS0 utmp + wtmp entry made
05/27 20:02:46 yS0 tio_set_flow_control( HARD XON_IN )
05/27 20:02:46 yS0 mdm_send: 'AT+FLO=2'
05/27 20:02:46 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:02:46 yS0 mdm_command: string 'OK' -> OK
05/27 20:02:46 yS0 11732 Mb free on /var/spool/fax/incoming
05/27 20:02:46 yS0 fax_send: 'AT+FDR'
05/27 20:02:46 yS0 fax_wait_for(CONNECT)
05/27 20:02:46 yS0 got:[0a][0d][0a]CONNECT[0d]
05/27 20:02:51 yS0 fax_wait_for: string 'CONNECT'** found **
05/27 20:02:51 yS0 sending DC2
05/27 20:02:51 yS0 11732 Mb free on /var/spool/fax/incoming
05/27 20:02:51 yS0 fax_get_page_data: wait for EOL, got:
[0a][ff][ff][ff][ff][ff][ff
][ff][ff][ff][fc][00]
05/27 20:02:51 yS0 fax_get_page_data: receiving
/var/spool/fax/incoming/ffa1dd49aS0-B
ehringer-Corp.01...
05/27 20:03:15 yS0 fax_get_page_data: page end, bytes received: 44312
05/27 20:03:15 yS0 fax_wait_for(OK)
05/27 20:03:15 yS0 got:[0d][0a]+FPS:1,2163,0,0,0[0d]
05/27 20:03:15 yS0 fax_wait_for: string '+FPS:1,2163,0,0,0'
05/27 20:03:15 yS0 page status: +FPS:1,2163,0,0,0
05/27 20:03:15 yS0 8547 lines received, 0 lines bad, 0 bytes lost
05/27 20:03:15 yS0 got:[0a][0d][0a]+FET:2[0d]
05/27 20:03:17 yS0 fax_wait_for: string '+FET:2'
05/27 20:03:17 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:03:17 yS0 fax_wait_for: string 'OK'** found **
05/27 20:03:17 yS0 fax_send: 'AT+FDR'
05/27 20:03:17 yS0 fax_wait_for(CONNECT)
05/27 20:03:17 yS0 got:[0a][0d][0a]+FHS:00[0d]
05/27 20:03:21 yS0 fax_wait_for: string '+FHS:00'
05/27 20:03:21 yS0 connection hangup: '+FHS:00'
05/27 20:03:21 yS0 (Normal and proper end of connection)** found **
05/27 20:03:21 yS0 fax receiver: hangup & end
05/27 20:03:21 yS0 fax_notify_mail: sending mail to: faxadmin
05/27 20:03:21 yS0 notify: '/etc/mgetty+sendfax/new_fax 0 'Behringer
Corp.' 1 /var/
spool/fax/incoming/ffa1dd49aS0-Behringer-Corp.01 >/dev/console 2>&1
</dev/null'
05/27 20:03:21 yS0 setenv: 'CALLER_ID=none'
05/27 20:03:21 yS0 setenv: 'CONNECT='
05/27 20:03:21 yS0 setenv: 'DEVICE=ttyS0'
05/27 20:03:21 ##### fax dev=ttyS0, pid=5871, caller='none', name='',
id='Behringer Co
rp.', +FHNG=000, pages=1/0, time=00:00:47

05/27 20:03:21 yS0 system() failed: No such file or directory
05/27 20:03:23 yS0 mdm_send: 'ATH0'
05/27 20:03:23 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:03:23 yS0 mdm_command: string 'OK' -> OK
05/27 20:03:23 yS0 removing lock file
--
05/27 20:03:23 yS0 mgetty: experimental test release 1.1.30-Dec16
05/27 20:03:23 yS0 check for lockfiles
05/27 20:03:23 yS0 checklock: stat failed, no file
05/27 20:03:23 yS0 locking the line
05/27 20:03:23 yS0 makelock(ttyS0) called
05/27 20:03:23 yS0 do_makelock: lock='/var/lock/LCK..ttyS0'
05/27 20:03:23 yS0 lock made
05/27 20:03:23 yS0 tio_get_rs232_lines: status: RTS CTS DSR DTR
05/27 20:03:23 yS0 lowering DTR to reset Modem
05/27 20:03:24 yS0 tss: set speed to 115200 (10002)
05/27 20:03:24 yS0 tio_set_flow_control( HARD )
05/27 20:03:24 yS0 waiting for line to clear (VTIME), read:
05/27 20:03:24 yS0 send: \dATQ0V1H0[0d]
05/27 20:03:24 yS0 waiting for ``OK''
05/27 20:03:24 yS0 got: [0d][0a]OK ** found **
05/27 20:03:25 yS0 send: ATS0=0Q0&D3&C1[0d]
05/27 20:03:25 yS0 waiting for ``OK''
05/27 20:03:25 yS0 got: [0d]
05/27 20:03:25 yS0 CND: OK[0a][0d][0a]OK ** found **
05/27 20:03:25 yS0 mdm_send: 'ATI'
05/27 20:03:25 yS0 got:[0d][0a][0d][0a]5601[0d]
05/27 20:03:25 yS0 mdm_gis: string 1: '5601'
05/27 20:03:25 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:03:25 yS0 mdm_identify: string '5601'
05/27 20:03:25 yS0 USR Courier/Sportster 56k detected
05/27 20:03:25 yS0 mdm_send: 'ATI3'
05/27 20:03:25 yS0 got:[0a][0d][0a]U.S. Robotics 56K FAX EXT V5.11.6[0d]
05/27 20:03:25 yS0 mdm_gis: string 1: 'U.S. Robotics 56K FAX EXT V5.11.6'
05/27 20:03:25 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:03:25 yS0 additional info: 'U.S. Robotics 56K FAX EXT V5.11.6'
05/27 20:03:25 yS0 mdm_send: 'AT+FCLASS=2.0'
05/27 20:03:25 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:03:25 yS0 mdm_command: string 'OK' -> OK
05/27 20:03:25 yS0 mdm_send: 'AT+FAA=1;+FCR=1'
05/27 20:03:25 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:03:25 yS0 mdm_command: string 'OK' -> OK
05/27 20:03:25 yS0 mdm_send: 'AT+FBO=1'
05/27 20:03:25 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:03:26 yS0 mdm_command: string 'OK' -> OK
05/27 20:03:26 yS0 mdm_send: 'AT+FNR=1,1,1,0'
05/27 20:03:26 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:03:26 yS0 mdm_command: string 'OK' -> OK
05/27 20:03:26 yS0 mdm_send: 'AT+FLI="973 697 4443"'
05/27 20:03:26 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:03:26 yS0 mdm_command: string 'OK' -> OK
05/27 20:03:26 yS0 mdm_send: 'AT+FCC=1,5,0,2,0,0,0,0'
05/27 20:03:26 yS0 got:[0a][0d][0a]OK[0d]
05/27 20:03:26 yS0 mdm_command: string 'OK' -> OK
05/27 20:03:26 yS0 waiting for line to clear (VTIME), read:
05/27 20:03:26 yS0 removing lock file
05/27 20:03:26 yS0 waiting...
[***@vrod log]#

--Boundary_(ID_ZB5oA1b4iD+D83ikIEElXw)
Content-type: text/html; charset=ISO-8859-1
Content-transfer-encoding: 7BIT

<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
<meta content="text/html;charset=ISO-8859-1" http-equiv="Content-Type">
</head>
<body bgcolor="#ffffff" text="#000000">
Gert Doering wrote:
<blockquote cite="mid:***@greenie.muc.de" type="cite">
<pre wrap="">Hi,

On Wed, May 27, 2009 at 08:31:04AM -0400, hylafax-user wrote:
</pre>
<blockquote type="cite">
<blockquote type="cite">
<blockquote type="cite">
<pre wrap="">A policy.h file sounds like it would be used in compiling a new version
of Mgetty. Since I don't have policy.h where would I add the
FAX_NOTIFY_PROGRAM line?
</pre>
</blockquote>
<pre wrap="">
If you have the source bundle, you have a policy.h-dist, and you have
a "README.1st". Guess what this is for :-)
</pre>
</blockquote>
<pre wrap="">I don't have the source bundle. I did read the README.1st and clicked
through the link to mgetty.greenie.net reading the receiving faxes
section which again points to policy.h or policy.h-dist.
I changed debug from 8 to 9 but don't see any difference in the log when
</pre>
</blockquote>
<pre wrap="">
Well, there's a download link on mgetty.greenie.net - but anyway,
thus should be doable without recompiling.

</pre>
<blockquote type="cite">
<pre wrap="">I reloaded mgetty after changing the /etc/mgetty+sendfax/mgetty.config

Here's the log:
</pre>
</blockquote>
<pre wrap="">[..]
</pre>
<blockquote type="cite">
<pre wrap="">05/27 08:16:43 yS0 additional info: 'U.S. Robotics 56K FAX EXT V5.11.6'
05/27 08:16:43 yS0 mdm_send: 'AT+FCLASS=2.0' -> OK
05/27 08:16:43 yS0 mdm_send: 'AT+FAA=1;+FCR=1' -> OK
</pre>
</blockquote>
<pre wrap="">
I'm not exactly sure what happened, but this is still "debug 4" level
(maybe you added the "debug 9" to an inactive "port" section in the
config file).

Try adding "-x 9" to the command line in /etc/inittab - this will
override whatever is in the config file.

</pre>
<blockquote type="cite">
<pre wrap="">Here's the mgetty.config
</pre>
</blockquote>
<pre wrap="">
Well - as I guessed:

</pre>
<blockquote type="cite">
<pre wrap=""># direct connection of a VT100 terminal which doesn't like DTR drops
#
#port ttyS3
# direct y
# speed 19200
# toggle-dtr n
fax-id 973 697 4443
fax-owner root
port /dev/modem
debug 9
fax-id 973 697 4443
speed 115200
init-chat ATM0DT
port-owner ppp
port-group pppusers
port-mode 0664
</pre>
</blockquote>
<pre wrap="">
These config statements will never be used, because they are behind
a section "port /dev/modem" - but your mgetty is running on "ttyS0".

This will never ever be evaluated, because the "port xxx" statement
must be without "/dev/" - and of course it must be the very same
device node that's put on the mgetty command line (ttyS0, without /dev/)

gert
</pre>
</blockquote>
All the while I thought the /dev/modem was how mgetty was working.  I
guess it was using compiled defaults. 
I changed the port statement to just say port ttyS0, of course then the
modem refused to answere because of the init-chat statement a few lines
down. 
I commented that out along with the port-owner, port-group and
port-mode statements (I had at one time been set up to allow dial-in
PPP). 
 
The log below is post changes.  You'd indicated we'd be able to get the
fax notify issue resolved without recompiling but didn't get into
details (probably 
because you'd found the /dev/modem issue.  
 
05/27 20:01:45 ##### failed dev=ttyS0, pid=5251, got signal 15, exiting 
 
-- 
05/27 20:01:58 yS0  mgetty: experimental test release 1.1.30-Dec16 
05/27 20:01:58 yS0  check for lockfiles 
05/27 20:01:58 yS0   checklock: stat failed, no file 
05/27 20:01:58 yS0  locking the line 
05/27 20:01:58 yS0   makelock(ttyS0) called 
05/27 20:01:58 yS0   do_makelock: lock='/var/lock/LCK..ttyS0' 
05/27 20:01:58 yS0   lock made 
05/27 20:01:59 yS0   tio_get_rs232_lines: status: RTS CTS DSR DTR 
05/27 20:01:59 yS0  lowering DTR to reset Modem 
05/27 20:01:59 yS0   tss: set speed to 115200 (10002) 
05/27 20:01:59 yS0   tio_set_flow_control( HARD ) 
05/27 20:01:59 yS0   waiting for line to clear (VTIME), read: 
05/27 20:01:59 yS0  send: \dATQ0V1H0[0d] 
05/27 20:02:00 yS0  waiting for ``OK'' 
05/27 20:02:00 yS0   got: [0d][0a]OK ** found ** 
05/27 20:02:00 yS0  send: ATS0=0Q0&D3&C1[0d] 
05/27 20:02:00 yS0  waiting for ``OK'' 
05/27 20:02:00 yS0   got: [0d] 
05/27 20:02:00 yS0    CND: OK[0a][0d][0a]OK ** found ** 
05/27 20:02:00 yS0  mdm_send: 'ATI' 
05/27 20:02:00 yS0    got:[0d][0a][0d][0a]5601[0d] 
05/27 20:02:00 yS0   mdm_gis: string 1: '5601' 
05/27 20:02:00 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:02:00 yS0   mdm_identify: string '5601' 
05/27 20:02:00 yS0  USR Courier/Sportster 56k detected 
05/27 20:02:00 yS0  mdm_send: 'ATI3' 
05/27 20:02:00 yS0    got:[0a][0d][0a]U.S. Robotics 56K FAX EXT
V5.11.6[0d] 
05/27 20:02:00 yS0   mdm_gis: string 1: 'U.S. Robotics 56K FAX EXT
V5.11.6' 
05/27 20:02:00 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:02:01 yS0  additional info: 'U.S. Robotics 56K FAX EXT V5.11.6' 
05/27 20:02:01 yS0  mdm_send: 'AT+FCLASS=2.0' 
05/27 20:02:01 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:02:01 yS0   mdm_command: string 'OK' -> OK 
05/27 20:02:01 yS0  mdm_send: 'AT+FAA=1;+FCR=1' 
05/27 20:02:01 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:02:01 yS0   mdm_command: string 'OK' -> OK 
05/27 20:02:01 yS0  mdm_send: 'AT+FBO=1' 
05/27 20:02:01 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:02:01 yS0   mdm_command: string 'OK' -> OK 
05/27 20:02:01 yS0  mdm_send: 'AT+FNR=1,1,1,0' 
05/27 20:02:01 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:02:01 yS0   mdm_command: string 'OK' -> OK 
05/27 20:02:01 yS0  mdm_send: 'AT+FLI="973 697 4443"' 
05/27 20:02:01 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:02:02 yS0   mdm_command: string 'OK' -> OK 
05/27 20:02:02 yS0  mdm_send: 'AT+FCC=1,5,0,2,0,0,0,0' 
05/27 20:02:02 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:02:02 yS0   mdm_command: string 'OK' -> OK 
05/27 20:02:02 yS0   waiting for line to clear (VTIME), read: 
05/27 20:02:02 yS0   removing lock file 
05/27 20:02:02 yS0  waiting... 
05/27 20:02:34 yS0    select returned 1 
05/27 20:02:34 yS0   checking lockfiles, locking the line 
05/27 20:02:34 yS0   makelock(ttyS0) called 
05/27 20:02:34 yS0   do_makelock: lock='/var/lock/LCK..ttyS0' 
05/27 20:02:34 yS0   lock made 
05/27 20:02:34 yS0  wfr: waiting for ``RING'' 
05/27 20:02:34 yS0   got: [0a][0d][0a]RING[0d] 
05/27 20:02:34 yS0    CND: RING 
05/27 20:02:34 yS0   wfr: rc=0, drn=0 
05/27 20:02:34 yS0    CND: check no: 'none' 
05/27 20:02:34 yS0  send: ATA[0d] 
05/27 20:02:34 yS0  waiting for ``CONNECT'' 
05/27 20:02:34 yS0   got: [0d] 
05/27 20:02:44 yS0    CND: OK[0a]+FCO[0d] 
05/27 20:02:44 yS0    CND: +FCO 
05/27 20:02:44 yS0  found action string: ``+FCO_'' 
05/27 20:02:44 yS0  start fax receiver... 
05/27 20:02:44 yS0   fax receiver: entry 
05/27 20:02:44 yS0  fax_wait_for(OK) 
05/27 20:02:44 yS0    got:[0a][0a][0d][0a]+FTI:"     Behringer
Corp."[0d] 
05/27 20:02:46 yS0   fax_wait_for: string '+FTI:"     Behringer Corp."' 
05/27 20:02:46 yS0  fax_id: '+FTI:"     Behringer Corp."' 
05/27 20:02:46 yS0    got:[0a][0d][0a]+FCS:1,5,0,2,0,0,0,0[0d] 
05/27 20:02:46 yS0   fax_wait_for: string '+FCS:1,5,0,2,0,0,0,0' 
05/27 20:02:46 yS0  transmission par.: '+FCS:1,5,0,2,0,0,0,0' 
05/27 20:02:46 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:02:46 yS0   fax_wait_for: string 'OK'** found ** 
05/27 20:02:46 yS0    looking for utmp entry... (my PID: 5871) 
05/27 20:02:46 yS0   utmp + wtmp entry made 
05/27 20:02:46 yS0   tio_set_flow_control( HARD XON_IN ) 
05/27 20:02:46 yS0  mdm_send: 'AT+FLO=2' 
05/27 20:02:46 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:02:46 yS0   mdm_command: string 'OK' -> OK 
05/27 20:02:46 yS0   11732 Mb free on /var/spool/fax/incoming 
05/27 20:02:46 yS0  fax_send: 'AT+FDR' 
05/27 20:02:46 yS0  fax_wait_for(CONNECT) 
05/27 20:02:46 yS0    got:[0a][0d][0a]CONNECT[0d] 
05/27 20:02:51 yS0   fax_wait_for: string 'CONNECT'** found ** 
05/27 20:02:51 yS0   sending DC2 
05/27 20:02:51 yS0   11732 Mb free on /var/spool/fax/incoming 
05/27 20:02:51 yS0   fax_get_page_data: wait for EOL, got:
[0a][ff][ff][ff][ff][ff][ff 
][ff][ff][ff][fc][00] 
05/27 20:02:51 yS0  fax_get_page_data: receiving
/var/spool/fax/incoming/ffa1dd49aS0-B 
ehringer-Corp.01... 
05/27 20:03:15 yS0  fax_get_page_data: page end, bytes received: 44312 
05/27 20:03:15 yS0  fax_wait_for(OK) 
05/27 20:03:15 yS0    got:[0d][0a]+FPS:1,2163,0,0,0[0d] 
05/27 20:03:15 yS0   fax_wait_for: string '+FPS:1,2163,0,0,0' 
05/27 20:03:15 yS0  page status: +FPS:1,2163,0,0,0 
05/27 20:03:15 yS0   8547 lines received, 0 lines bad, 0 bytes lost 
05/27 20:03:15 yS0    got:[0a][0d][0a]+FET:2[0d] 
05/27 20:03:17 yS0   fax_wait_for: string '+FET:2' 
05/27 20:03:17 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:03:17 yS0   fax_wait_for: string 'OK'** found ** 
05/27 20:03:17 yS0  fax_send: 'AT+FDR' 
05/27 20:03:17 yS0  fax_wait_for(CONNECT) 
05/27 20:03:17 yS0    got:[0a][0d][0a]+FHS:00[0d] 
05/27 20:03:21 yS0   fax_wait_for: string '+FHS:00' 
05/27 20:03:21 yS0  connection hangup: '+FHS:00' 
05/27 20:03:21 yS0   (Normal and proper end of connection)** found ** 
05/27 20:03:21 yS0   fax receiver: hangup & end 
05/27 20:03:21 yS0   fax_notify_mail: sending mail to: faxadmin 
05/27 20:03:21 yS0   notify: '/etc/mgetty+sendfax/new_fax 0 'Behringer
Corp.' 1  /var/ 
spool/fax/incoming/ffa1dd49aS0-Behringer-Corp.01 >/dev/console
2>&1 </dev/null' 
05/27 20:03:21 yS0   setenv: 'CALLER_ID=none' 
05/27 20:03:21 yS0   setenv: 'CONNECT=' 
05/27 20:03:21 yS0   setenv: 'DEVICE=ttyS0' 
05/27 20:03:21 ##### fax dev=ttyS0, pid=5871, caller='none', name='',
id='Behringer Co 
rp.', +FHNG=000, pages=1/0, time=00:00:47 
 
 
05/27 20:03:21 yS0  system() failed: No such file or directory 
05/27 20:03:23 yS0  mdm_send: 'ATH0' 
05/27 20:03:23 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:03:23 yS0   mdm_command: string 'OK' -> OK 
05/27 20:03:23 yS0   removing lock file 
-- 
05/27 20:03:23 yS0  mgetty: experimental test release 1.1.30-Dec16 
05/27 20:03:23 yS0  check for lockfiles 
05/27 20:03:23 yS0   checklock: stat failed, no file 
05/27 20:03:23 yS0  locking the line 
05/27 20:03:23 yS0   makelock(ttyS0) called 
05/27 20:03:23 yS0   do_makelock: lock='/var/lock/LCK..ttyS0' 
05/27 20:03:23 yS0   lock made 
05/27 20:03:23 yS0   tio_get_rs232_lines: status: RTS CTS DSR DTR 
05/27 20:03:23 yS0  lowering DTR to reset Modem 
05/27 20:03:24 yS0   tss: set speed to 115200 (10002) 
05/27 20:03:24 yS0   tio_set_flow_control( HARD ) 
05/27 20:03:24 yS0   waiting for line to clear (VTIME), read: 
05/27 20:03:24 yS0  send: \dATQ0V1H0[0d] 
05/27 20:03:24 yS0  waiting for ``OK'' 
05/27 20:03:24 yS0   got: [0d][0a]OK ** found ** 
05/27 20:03:25 yS0  send: ATS0=0Q0&D3&C1[0d] 
05/27 20:03:25 yS0  waiting for ``OK'' 
05/27 20:03:25 yS0   got: [0d] 
05/27 20:03:25 yS0    CND: OK[0a][0d][0a]OK ** found ** 
05/27 20:03:25 yS0  mdm_send: 'ATI' 
05/27 20:03:25 yS0    got:[0d][0a][0d][0a]5601[0d] 
05/27 20:03:25 yS0   mdm_gis: string 1: '5601' 
05/27 20:03:25 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:03:25 yS0   mdm_identify: string '5601' 
05/27 20:03:25 yS0  USR Courier/Sportster 56k detected 
05/27 20:03:25 yS0  mdm_send: 'ATI3' 
05/27 20:03:25 yS0    got:[0a][0d][0a]U.S. Robotics 56K FAX EXT
V5.11.6[0d] 
05/27 20:03:25 yS0   mdm_gis: string 1: 'U.S. Robotics 56K FAX EXT
V5.11.6' 
05/27 20:03:25 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:03:25 yS0  additional info: 'U.S. Robotics 56K FAX EXT V5.11.6' 
05/27 20:03:25 yS0  mdm_send: 'AT+FCLASS=2.0' 
05/27 20:03:25 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:03:25 yS0   mdm_command: string 'OK' -> OK 
05/27 20:03:25 yS0  mdm_send: 'AT+FAA=1;+FCR=1' 
05/27 20:03:25 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:03:25 yS0   mdm_command: string 'OK' -> OK 
05/27 20:03:25 yS0  mdm_send: 'AT+FBO=1' 
05/27 20:03:25 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:03:26 yS0   mdm_command: string 'OK' -> OK 
05/27 20:03:26 yS0  mdm_send: 'AT+FNR=1,1,1,0' 
05/27 20:03:26 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:03:26 yS0   mdm_command: string 'OK' -> OK 
05/27 20:03:26 yS0  mdm_send: 'AT+FLI="973 697 4443"' 
05/27 20:03:26 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:03:26 yS0   mdm_command: string 'OK' -> OK 
05/27 20:03:26 yS0  mdm_send: 'AT+FCC=1,5,0,2,0,0,0,0' 
05/27 20:03:26 yS0    got:[0a][0d][0a]OK[0d] 
05/27 20:03:26 yS0   mdm_command: string 'OK' -> OK 
05/27 20:03:26 yS0   waiting for line to clear (VTIME), read: 
05/27 20:03:26 yS0   removing lock file 
05/27 20:03:26 yS0  waiting... 
[***@vrod log]#  
 
</body>
</html>

--Boundary_(ID_ZB5oA1b4iD+D83ikIEElXw)--

Gert Doering

2009-05-30 11:16:23 UTC

Permalink

Hi,

(as a side note: the e-mail address that you're using is unreachable, so
I get bounces for every mail I send. Somewhat annoying)

Post by hylafax-user
05/27 20:03:21 yS0 connection hangup: '+FHS:00'
05/27 20:03:21 yS0 (Normal and proper end of connection)** found **
05/27 20:03:21 yS0 fax receiver: hangup & end
05/27 20:03:21 yS0 fax_notify_mail: sending mail to: faxadmin
05/27 20:03:21 yS0 notify: '/etc/mgetty+sendfax/new_fax 0 'Behringer Corp.' 1 /var/spool/fax/incoming/ffa1dd49aS0-Behringer-Corp.01 >/dev/console 2>&1 </dev/null'

Well, here you go - this is the command that mgetty calls after a fax has
been received: /etc/mgetty+sendfax/new_fax.

Try calling this with the same arguments from the command line:

# /etc/mgetty+sendfax/new_fax 0 'Behringer Corp.' 1 /var/spool/fax/incoming/ffa1dd49aS0-Behringer-Corp.01

(mind the quotes)

to easily see where the errors come from.

gert